9. CONNECTOR PINOUTS
This page describes the pinouts of various connectors available on Athena IV.
9.1 Power [J11]
A 1x9 2.54mm pitch header is used as power connector. Pinouts are as shown below:
Connector Type: 1x6 2.54mm vertical pin header
Connector PN: Aptos# LHY-40S-VB-060/030-FG
Mating Cable PN: 698009
9.2 HDD Power Out [J12]
A 1x4 2.54mm pitch RA connector is used to supply power for hard disk drives. Pinouts are as shown below:
Connector Type: 1x4 2.54mm right angle frictional lock connector
Connector PN: Tyco# 640457-4
Mating Cable PN: 6981006
9.3 External RTC Battery [J9]
A 1x2 2.54mm RA connector is used to connect external battery for RTC. Pinouts are as shown below:
Connector Type: 1x2 2.54mm right angle frictional lock connector
Connector PN: Tyco# 640457-2
Mating Cable PN: 6981011
9.4 Ethernet Ports
9.4.1 ETH-1 [J4]
A 2x6 2.54mm pitch header is used to access the ETH-1 port. Pinouts are as shown below:
Connector Type: 2x6 2.54mm vertical pin header
Connector PN: Oupiin# 2011-2X40G00SD025/SN
Mating Cable PN: C-PRZ-02 (100 Mbps) or 6981086 (1 Gbps)
9.4.2 ETH-2 [J19]
A 2x5 2mm header connector is used to access the ETH-2 port. Pinouts are as shown below:
Connector Type: 2x5 2mm vertical pin header
Connector PN: Pinrex# 220-97-36GB01
Mating Cable PN: 6981080
9.5 VGA [J25]
A 2x5 2.54mm pitch header connector is used to access the VGA on Athena IV. Pinouts are as shown below:
Connector Type: 2x6 2.54mm vertical pin header
Connector PN: Oupiin# 2011-2X40G00SD02A53/2S
Mating Cable PN: 6981030
9.6 LVDS [J24]
The LVDS interface is terminated on a 2x15 1mm pitch connector. Pinouts are as shown below:
Connector Type: 2x15 1mm vertical connector
Connector PN: JST# BM30B-SHLDS-G-TFT(LF)(SN)
Mating Cable PN: Custom (LVDS cable is not part of standard cable kit)
Mating Connector: JST# SHDR-30V-S-B
Mating Terminals: JST# SSH-003GA-P0.2
9.7 LVDS Backlight [J8]
The LVDS backlight signals are terminated on a 1x6 1.25mm connector. Pinouts are as shown below:
Connector Type: 1x6 1.25mm right angle connector
Connector PN: Molex# 53261-0671
Mating Cable PN: Custom (LVDS backlight cable is not part of standard cable kit)
Mating Connector: Molex# 51021-0600
Mating Terminals: Molex# 50058
9.8 Audio [J15]
A 2x5 2.54mm pitch header connector is used to access audio on Athena IV. Pinouts are as shown below:
Connector Type: 2x5 2.54mm
Connector PN: Oupiin# 2011-2X40G00SD02A53/2S
Mating Cable PN: 6981031
9.9 USB2.0 Ports [J5, J21]
There are two USB2.0 connectors with identical pinouts terminated on 2x5 2.54mm pitch header connectors. Each connector provides access to two USB 2.0 ports. Pinouts are as shown below:
Connector Type: 2x5 2.54mm vertical pin header
Connector PN: Oupiin# 2011-2X40G00SD02A53/2S
Mating Cable PN: 6981012
9.10 USB3.0 [J7]
A 2x5 2mm pitch vertical connector is used to access the USB3.0 port on Athena IV. Pinouts are as shown below:
Connector Type: 2x5 2mm vertical connector
Connector PN: Amphenol# 98414-G06-10ULF
Mating Cable PN: 6980603
9.11 SATA [J26]
A SATA interface is terminated on a standard 7-pin vertical connector. Pinouts are as shown below:
Connector Type: Standard 7-pin vertical SATA connector
Connector PN: Molex# 678008025
Mating Cable PN: Standard SATA cable
9.12 Data Acquisition (DAQ) [J14]
A 2x25 2.54mm pitch connector is used to access the analog & digital I/Os of Athena IV. Pinouts are as shown below:
Connector Type: 2x25 2.54mm vertical pin header
Connector PN: Oupiin# 2011-2X40G00SD02
Mating Cable PN: C-50-18
9.13 Serial Ports & Legacy I/O [J3]
Serial ports, & legacy I/O signals are terminated on a high-density 80-pin connector. Pinouts are as shown below:
1
IDE^
1
IDE RST
2
2
Ground
3
RXD 1
3
IDE DD7
4
RTS 1
4
IDE DD8
COM 1
5
TXD 1
5
IDE DD6
6
CTS 1
6
IDE DD9
7
7
IDE DD5
8
8
IDE DD10
9
Ground
9
IDE DD4
10
10
IDE DD11
11
11
IDE DD3
12
RXD 2
12
IDE DD12
13
RTS 2
13
IDE DD2
COM 2
14
TXD 2
14
IDE DD13
15
CTS 2
15
IDE DD1
16
16
IDE DD14
17
17
IDE DD0
18
Ground
18
IDE DD15
19
19
DRQ/Ground*
20
20
IDE Detect
21
RXD 3
21
IOW
22
RTS 3
22
Ground
COM 3
23
TXD 3
23
IOR
24
CTS 3
24
Ground
25
25
IO RDY
26
26
RESET/Ground*
27
Ground
27
DACK3
28
PWR_BTN*
28
Ground
29
[RST*]
29
IRQ14
30
RXD 4
30
IDE DA1
31
RTS 4
31
GND
COM 4
32
TXD 4
32
IDE DA0
33
CTS 4
33
IDE DA2
34
I2C CLK*
34
IDE CS0/Ground*
35
I2C Data*
35
IDE CS1/RESET*
36
Ground
36
DASPn /PWR_BTN*
37
+5V Out
37
GND/NC*
Utilities A
38
Speaker Out
38
+5V/NC*
39
SATA Drive LED
39
+5V/NC*
40
Power LED
40
Ground/NC*
Note:
*The signals are multiplexed with 0E.
^ The IDE interface is no longer used on Athena IV.
Connector Type: 80-pin connector
Connector PN: 3M# P50E-080P1-S1-EA
Mating Cable PN: C-PRZ-01 or 6981014
9.14 JTAG [J16]
A 1x6 2.54mm pitch header connector is used to program the FPGA with JTAG interface. Pinouts are as shown below:
Connector Type: 1x6 2.54mm vertical pin header
Connector PN: Aptos# LHY-40S-VB-060/030-FG
Mating Cable PN: NA
Last updated
Was this helpful?